Mod Details
PremiumNo Difficulty![](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/menu-normal-over.png)
![](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/menu-normal-over.png)
![](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/menu-normal-off.png)
![](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/menu-normal-off.png)
![](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/menu-normal-off.png)
![453 Fortwo/Forfour 453 Fortwo/Forfour](https://www.evilution.co.uk/wp-content/themes/evilution/images/evilution/model8.png)
Remove the front bumper so you can access a bolt later on. Open the door and look at the lower part of the door shut. These bolts are 10mm with a Torx30 inside. You can use either size tools to remove them.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch1.jpg)
Look to the top of the door shut to the black triangle in front of the wing mirrors. There’s a plastic rivet, lever this forwards with a trim tool. Then pull the entire part out.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch2.jpg)
The plastic cover can now be pulled directly from the car. It’s just clipped in.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch3.jpg)
Underneath is another 10mm/Torx30 bolt to remove.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch4.jpg)
At the back of the wheel arch there’s another plastic rivet.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch5.jpg)
Again, with a trim tool, lever the centre out and then pull the whole clip out.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch6.jpg)
Remove the bonnet (service panel) and look at the bottom corners of the windscreen.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch7.jpg)
Pull these rubber covers upwards to remove them.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch8.jpg)
Underneath you’ll find a Torx30 bolt to remove.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch9.jpg)
On the inside leading edge of the arch panel you’ll find another pair of Torx30 bolts to remove.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch10.jpg)
Between the 2 previous bolts, at the base of the scuttle panel is a foam piece…
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch11.jpg)
… that can be pulled out to reveal…
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch12.jpg)
…another 10mm/Torx30 bolt to remove.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch13.jpg)
Open the door slightly. Just behind the side indicator you’ll see a black clip. It makes life a lot easier if you put a trim tool or flat blade screw driver in between the clip and panel. It opens the clip up enough to allow the panel to be pulled sideways to unclip it.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch14.jpg)
Once the panel has cleared the clip…
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch15.jpg)
…reach up under the panel and disconnect the indicator bulb holders by twisting them a quarter turn.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch16.jpg)
Look at the front edge of the wing, just below the the headlight.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch17.jpg)
Another two Torx30 bolt to remove.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch18a.jpg)
With that final bolt removed, the wing can be removed from the car.
![](/wp-content/uploads/smartexterior/panels/453/arch/453arch19.jpg)
Job done.